Search found 238 matches

by volrem
Tue Jan 01, 2019 12:32 pm
Forum: Diagnostic discussion
Topic: Inverted waveforms with TA204 handheld COP probe?
Replies: 15
Views: 500

Re: Inverted waveforms with TA204 handheld COP probe?

Change the linear equation under scaling method to use minus in formula. y=-10000 not y=10000 This way you can get inverted waveform. Not sure about this invert function under manual ranges. It doesn't work for me either but to be onest I have never tried that before. Always used minus in formula an...
by volrem
Sun Dec 30, 2018 6:18 pm
Forum: Diagnostic discussion
Topic: Inverted waveforms with TA204 handheld COP probe?
Replies: 15
Views: 500

Re: Inverted waveforms with TA204 handheld COP probe?

Use custom probe instead. Use built in probe, make a copy of that and edit to your ranges and invert if needed.

This way you can use it live. You have to install older Pico version though because latest is faulty and crashes on probe editing.
by volrem
Mon Dec 17, 2018 7:02 pm
Forum: PicoScope 6 Automotive software
Topic: problems with picoscope 6.13.6 on windows 10
Replies: 22
Views: 1530

Re: problems with picoscope 6.13.6 on windows 10

Because they use phased roll-out. Update via Picoscope will be activated little bit later.

viewtopic.php?p=93141#p93141
by volrem
Mon Dec 17, 2018 7:43 am
Forum: PicoScope 6 Automotive software
Topic: Maths is cool (but I cannot get it to work)
Replies: 25
Views: 734

Re: Maths is cool (but I cannot get it to work)

Thanks Steve

And heading is old beacause I quoted old post with old heading. Don't waste time looking into it.
by volrem
Sun Dec 16, 2018 7:44 pm
Forum: PicoScope 6 Automotive software
Topic: problems with picoscope 6.13.6 on windows 10
Replies: 22
Views: 1530

Re: problems with picoscope 6.13.6 on windows 10

Don't use auto-update. Download new installer from website.
by volrem
Sat Dec 15, 2018 6:34 pm
Forum: PicoScope 6 Automotive software
Topic: Maths is cool (but I cannot get it to work)
Replies: 25
Views: 734

Re: Maths is cool (but I cannot get it to work)

Hi Steve Downloaded edited file and Pico still crashes. I'm on another computer though. BTW 60/48*freq(A)*1.9625*60/1000 and 1.25*freq(A)*0.11775 work fine for me. But when in demo mode and creating math channel 60/48*freq(A)*(3.14 * 0.625)*60/1000 crashes Pico. I can enter thos formula (no red cro...
by volrem
Sat Nov 24, 2018 10:12 pm
Forum: PicoScope 6 Automotive software
Topic: Using the rotational rulers
Replies: 16
Views: 533

Re: Using the rotational rulers

pico2.png Crank signal with 60-2 tooth pattern in red. Graphed engined speed from crank sensor signal in black. 360 degrees marked and partitioned evenly by 60 degrees. Each crank tooth is 6 degrees. If engine would run at constant speed all the time then partition rulers should be at the same plac...
by volrem
Fri Nov 09, 2018 8:22 pm
Forum: PicoScope 6 Automotive software
Topic: Maths is cool (but I cannot get it to work)
Replies: 25
Views: 734

Re: Maths is cool

Hi Steve Downloaded edited file and Pico still crashes. I'm on another computer though. BTW 60/48*freq(A)*1.9625*60/1000 and 1.25*freq(A)*0.11775 work fine for me. But when in demo mode and creating math channel 60/48*freq(A)*(3.14 * 0.625)*60/1000 crashes Pico. I can enter thos formula (no red cros...
by volrem
Fri Nov 09, 2018 2:12 pm
Forum: PicoScope 6 Automotive software
Topic: Maths is cool (but I cannot get it to work)
Replies: 25
Views: 734

Re: Maths is cool

I wanted to try this ABS to road speed but my Pico just crashed when opening that.

Trace attached if interested,
by volrem
Fri Nov 09, 2018 2:08 pm
Forum: PicoScope 6 Automotive software
Topic: Maths is cool (but I cannot get it to work)
Replies: 25
Views: 734

Re: Maths is cool

I personally think that Pico should stop using regional settings and hard code decimal and other things. So that formula in England would work the same way as in Denmark or in Estonia. Biggest problem is that in Estonia we use "," as decimal but you use "." You have "," for digit grouping. We have "...