Search found 226 matches

by KimAndersen
Mon Feb 15, 2021 8:27 pm
Forum: Diagnostic discussion
Topic: SENT vacuum sensor??
Replies: 7
Views: 911

Re: SENT vacuum sensor??

Hi Here is a link to an earlier post regarding decoding a rail pressure sensor where Ben Martins and I describe in detail the problems that can be with the decoding of various SENT sensors. https://www.picoauto.com/support/topic22061.html I think one of the reasons you do not see any data being deco...
by KimAndersen
Sat Dec 19, 2020 11:34 am
Forum: PicoScope 6 Automotive software
Topic: Current Clamp Problems
Replies: 1
Views: 1564

Re: Current Clamp Problems

Hi martinnr I do not know if it is quite the same problem you have with your current clamp as I had with my low current clamp. You can read what my problem was in this post. I can say so much that - it was driving me crazy. https://www.picoauto.com/support/topic21291.html Hope you fi...
by KimAndersen
Thu Nov 05, 2020 3:30 pm
Forum: PicoScope 6 Automotive software
Topic: K-Line Serial Decoding Support?
Replies: 9
Views: 3624

Re: K-Line Serial Decoding Support?

Hi Ashtray1987

As Ben mentioned - try uploading your K-line psdata file and explain to us what your problem is or what you would like to know and maybe I can help you a little. :wink:

Regards
Kim
by KimAndersen
Mon Jul 27, 2020 5:17 pm
Forum: Heavy Duty and Off Highway
Topic: Smart Sensors
Replies: 23
Views: 7900

Re: Smart Sensors

Hi muttnjeff I can not display anything from the J1939DA document based on SAE.ORG's copyrights or anything else - I dare not. Regarding your question about sensor reporting, this document is very detailed regarding PGN and SPN numbers about where and what the individual bytes / bits have been used ...
by KimAndersen
Sun Jul 26, 2020 8:46 am
Forum: Heavy Duty and Off Highway
Topic: Smart Sensors
Replies: 23
Views: 7900

Re: Smart Sensors

Hi What an interesting topic - the interpretation of the J1939 protocol. I have to admit that I have been following this topic from the beginning and thought it could be exciting and so is it. But in what way can I help you understand the J1939 protocol and its operation !. Ben has described most of...
by KimAndersen
Sun Jul 12, 2020 2:18 pm
Forum: Help me fix my car
Topic: Kia Sportage 2011 performance
Replies: 3
Views: 2402

Re: Kia Sportage 2011 performance

Hi Wim It is a broadband oxygen sensor used before the catalyst converter on this Kia Sportage. As for your voltage measurement from this broadband sensor is good or bad is hard to say but I know this sensor works with a voltage range from 0 mV to 4500 mV - so you are not out of specifications with ...
by KimAndersen
Tue May 19, 2020 9:09 pm
Forum: Diagnostic discussion
Topic: A Shout for help.
Replies: 7
Views: 3066

Re: A Shout for help.

With that said, it is not possible and I don't recall a G450 Kim on this vehicle. It does have an EGR Heat exchanger/cooler but no By-Pass arrangement about this cooler. If the engine is fitted with a particle filter, there must also be an exhaust gas pressure (G450) mounted somewhere in the engine...
by KimAndersen
Sat May 16, 2020 5:07 pm
Forum: Diagnostic discussion
Topic: A Shout for help.
Replies: 7
Views: 3066

Re: A Shout for help.

Hi Steve I don't know if this will help you in your quest for a diagnostic answer to this Seat Alhambra 2.0 TDI. A few years ago I uploaded a file to the waveform library over an exhaust gas pressure sensor (G450) - which is mounted in a VW Jetta 2.0 TDI - engine type BMM model year 2008. In my opin...
by KimAndersen
Sun Mar 22, 2020 10:42 am
Forum: Diagnostic discussion
Topic: Peugeot 207 1.4vti
Replies: 5
Views: 1819

Re: Peugeot 207 1.4vti

Hi

This image is taken from a Peugeot 207 1.4 VTI - I know it's not a picoscope psdata file that you can play with, but by looking visible at the image - I would say the cam and crank timing are out of spec.

Peugeot 207 1.4 VTI CAM AND CRANK RELATIONSHIP
Peugeot 207 1.4 VTI CAM AND CRANK RELATIONSHIP
Best regards
Kim :wink:
by KimAndersen
Sat Feb 29, 2020 11:25 pm
Forum: Case studies
Topic: High pressure fuel sensor no ground, SENT signal
Replies: 11
Views: 10709

Re: High pressure fuel sensor no ground, SENT signal

I managed to find the correct part number of this rail pressure sensor which is used in this particular engine type 4.0 Litre TFSI V8. The spare part number of this sensor is 06L906054C which have a pressure range at 0 to 350 bar and are manufactored by Sensata. For those who are interested in decod...