Search found 182 matches

by Iver
Wed Jun 19, 2019 3:22 pm
Forum: Diagnostic discussion
Topic: Peugeot 308cc RHF Engine Will not start
Replies: 10
Views: 13259

Re: Peugeot 308cc RHF Engine Will not start

Landroverman. I have not looked at this car recently but can confirm that we did a Leak off test. Rather unconventional but we did not attach pipes or bottles, however on a good 30 seconds of cranking no fuel was seen from any injectors. Fuel Pressure did exist in the rail at time of test. I agree w...
by Iver
Sun Jun 16, 2019 2:03 pm
Forum: PicoDiagnostics NVH
Topic: buying NVH
Replies: 5
Views: 8491

Re: buying NVH

and maybe a wps too.
everyone needs a WPS !! Superb tool, sets the Men & Boys apart !!
Getting expensive this! 😀😎🤟
No Pain No Gain Jim ! :D :D
by Iver
Sun Jun 16, 2019 1:41 pm
Forum: Automotive kit hardware
Topic: What kit to buy
Replies: 2
Views: 4054

Re: What kit to buy

(1) Ignition -distributor type- primary and secondary readings; 2 Channels will allow you to look at 1 Primary and One Secondary a a time or just 2 secondaries unless you add the Mixmaster ...
by Iver
Sun Jun 16, 2019 1:23 pm
Forum: Case studies
Topic: 2018 Camaro reduced engine power
Replies: 4
Views: 13937

Re: 2018 Camaro reduced engine power

Hi Ben

Great catch there. Perseverance pays off !!

When I find something like this is always "how did that happen?"

Do you think that was bad manufacture, vibrating Harness or someone been there before ?

( I didn't see corrosion in the picture)
by Iver
Sun Jun 16, 2019 1:13 pm
Forum: PicoDiagnostics NVH
Topic: VOLVO FH 2012
Replies: 1
Views: 5716

Re: VOLVO FH 2012

But tires arent possible to enter 295/80r22.5 is says its no valid dimension. So entered 22 and a correction factor. www.picoauto.com/support/viewtopic.php?t=21639 that post suggests that the half sizes in commercial tyres is in t...
by Iver
Mon Jun 10, 2019 10:52 pm
Forum: Help me fix my car
Topic: P0171
Replies: 7
Views: 9212

Re: P0171

what constitutes a full cycle run?
A Minimum Quarter tank of Fuel is one of many Prerequisites that have been overlooked by some. So much easier to achieve the drive cycles on the manufacturers test tracks as opposed to the busy roads we have where it is not easy, Especially between 9 - 5am ?
by Iver
Mon Jun 10, 2019 8:45 pm
Forum: Diagnostic discussion
Topic: Peugeot 308cc RHF Engine Will not start
Replies: 10
Views: 13259

Re: Peugeot 308cc RHF Engine Will not start

This DTC P0215 is the supply power to the ECU and despite your great effort to check this relay - would I take a closer look at this relay and the power supply to the ECU once more - just to be 100 % sure. You could make a bypass wire to the ECU - just to verify !!!. I dont have a wiring diagram, s...
by Iver
Mon Jun 10, 2019 12:36 pm
Forum: Diagnostic discussion
Topic: 2014 VW Crafter Cutting out on hot re-start p0016
Replies: 7
Views: 20715

Re: 2014 VW Crafter Cutting out on hot re-start p0016

did you get to the bottom of the hot start problem as I have one exactly the same that we are struggling with at the moment. I had a Crafter recently that would not start when hot, however I had a different set of fault codes and I did solve it. Do you have the same codes or are you able to list th...
by Iver
Mon Jun 10, 2019 12:13 pm
Forum: Diagnostic discussion
Topic: Peugeot 308cc RHF Engine Will not start
Replies: 10
Views: 13259

Re: Peugeot 308cc RHF Engine Will not start

Not so sure now what I was measuring or how those voltages occurred. It was a few weeks ago that I looked at the car. I have learnt today from the Garage that A Genuine New BSI has been fitted & coded. Another Engine ECU has been Matched & Fitted. The Old EcU is now back on the car. This parts were ...
by Iver
Sun Jun 09, 2019 11:35 am
Forum: Diagnostic discussion
Topic: Peugeot 308cc RHF Engine Will not start
Replies: 10
Views: 13259

Re: Peugeot 308cc RHF Engine Will not start

Hi Guys, and thanks for the great replies. why don't you check your pids for fuel pressure,desired v actual?check your rail pressure sensor circuit plausibility by unplugging sensor,and looking at open circuit code Having read both replies now I am not quite sure about rail pressure, it was 2 weeks ...