Search found 69 matches

by terbo
Sun Apr 22, 2018 7:48 pm
Forum: Diagnostic discussion
Topic: Polo 1,2 3-Cyl. - WPS 500 Pressure Question
Replies: 17
Views: 35157

Re: Polo 1,2 3-Cyl. - WPS 500 Pressure Question

Hi, @kona You mean a relative Compression Test ? Or WPS Readings of each Cylinder ? The Car starts fine, idles fine, revs up fine, no error Codes set, all Readiness Monitors run - Short Term is at around -10% - so far so good .) But the Cat starts GLOWING red Hot after a short time driving, or even ...
by terbo
Sun Apr 22, 2018 10:22 am
Forum: Diagnostic discussion
Topic: Polo 1,2 3-Cyl. - WPS 500 Pressure Question
Replies: 17
Views: 35157

Polo 1,2 3-Cyl. - WPS 500 Pressure Question

Hi, Looking at a 2006 1,2 L 3-Cyl. BMD-Engine in a Polo i did a Snap-Throttle Capture. Car has a VERY long story to it,but that is maybe for a later Post. What i can not get in sync in my Head is, why is there a second pressure after the Compression when snapping it, while at idle the Pattern looks ...
by terbo
Mon Jul 03, 2017 6:28 pm
Forum: Help me fix my car
Topic: Ford Focus 2001 1,6 Zetec-SE
Replies: 23
Views: 24194

Re: Ford Focus 2001 1,6 Zetec-SE

Hi, No, to my suprise, the car did crank and start and if you heard it, you would never thought that this Piece would look that way. There was no "CLUNK" and "BONK" or big loud rattleing.... Only thing i thought of before, it sounded like a plugged exhaust. As long as it was screwed to the Engine, i...
by terbo
Sun Jul 02, 2017 7:27 pm
Forum: Help me fix my car
Topic: Ford Focus 2001 1,6 Zetec-SE
Replies: 23
Views: 24194

Re: Ford Focus 2001 1,6 Zetec-SE

As Eric O. would say : THERE IS YOUR PROBLEM, LADY :)
Car pures like brand new....0 Error codes present, Full Power
and not 1 Misfire.Vacuum readings steady and at normal specs.

Will do some after Waveforms in the next Week or so, but just
follow up, and not leave this open-ended....
by terbo
Sun Jun 11, 2017 11:42 am
Forum: Help me fix my car
Topic: Ford Focus 2001 1,6 Zetec-SE
Replies: 23
Views: 24194

Re: Ford Focus 2001 1,6 Zetec-SE

The mechanical timing is correct.
Put in Timing tool, turned Crank till it stopped, and
the Tool for the CAMs slides in with no pressure.
1 FInger > CLICK - inserted
by terbo
Mon Jun 05, 2017 11:16 am
Forum: Help me fix my car
Topic: Ford Focus 2001 1,6 Zetec-SE
Replies: 23
Views: 24194

Re: Ford Focus 2001 1,6 Zetec-SE

At "idle" , if you get it to rev up a little
then you get around 20 on the Decel for
about 1 second, if you let it idle, it drops
and drops till around 3, then Engine cuts out.
by terbo
Sun Jun 04, 2017 2:10 pm
Forum: Help me fix my car
Topic: Ford Focus 2001 1,6 Zetec-SE
Replies: 23
Views: 24194

Re: Ford Focus 2001 1,6 Zetec-SE

Hi,
I think FYDB is not so incorrect, think that could be.
But i don´t know 100%.
Where do i find the engine code on this Car ?
Partslink doen´t show it with the VIN.
Pord Service Page either...
by terbo
Sun Jun 04, 2017 11:59 am
Forum: Help me fix my car
Topic: Ford Focus 2001 1,6 Zetec-SE
Replies: 23
Views: 24194

Ford Focus 2001 1,6 Zetec-SE

Hi, I got a Focus in, that starts really bad, idles poorly, almost doesn´t rev, only if you hit it WOT then it slowly increases rpm. Sounds like it would have a plugged exhaust.But same with Cat taken off. And makes puffing noises from engine bay when it dies off at idle. Checked Codes - nothing Che...
by terbo
Tue May 23, 2017 11:39 am
Forum: Diagnostic discussion
Topic: Smart 450 sometimes not charging
Replies: 0
Views: 4768

Smart 450 sometimes not charging

Hi, Friend of mine has a (Mercedes) Smart 450 that sometimes doesn´t charge. His Garage put in a new alternator, but same thing happens. The alternator has a Big Wire to Battery and one to ground, and one small one called PH-IN coming from the Engine ECU - Pin 47. I yesterday took a peak at this wir...
by terbo
Sun Dec 18, 2016 10:05 am
Forum: Help me fix my car
Topic: Golf 4 1999 - Mis- and Backfires
Replies: 6
Views: 11357

Re: Golf 4 1999 - Mis- and Backfires

The Car is fixed....thinking about it, it was simple. As written before : Basic things. What does a engine need ? Fuel, Air, Compression. WHat was not changed ? The Injectors. Pulled the Mainifold, cycled the key, put the OTC 3398 on the Injectors, looked at the fuel Pressure gauge, and - NOT ONE wa...