Search found 13 matches

by Automod
Sat Oct 05, 2019 7:02 pm
Forum: Diagnostic discussion
Topic: Merc E220 bluetec 2015
Replies: 7
Views: 413

Re: Merc E220 bluetec 2015

This is driving me crazy, before I send this car to Merc can anyone else shed some light on this please.... Put a brand new Nox on but still get a code that its faulty, but everything else check out, and 3 key ons to ignition brings an Ad blue fault. Have tried re-learning but this code remains. I c...
by Automod
Fri Sep 27, 2019 5:37 pm
Forum: Diagnostic discussion
Topic: Merc E220 bluetec 2015
Replies: 7
Views: 413

Re: Merc E220 bluetec 2015

So a little update, after borrowing someone's Xentry machine I managed to do full diagnostics, followed every step and everything comes back successfull??? There is only one code now saying component failure, but also if turn the key of and start it up again 3 or 4 times the engine light comes on an...
by Automod
Sun Sep 22, 2019 10:11 am
Forum: Diagnostic discussion
Topic: Merc E220 bluetec 2015
Replies: 7
Views: 413

Re: Merc E220 bluetec 2015

Hi thank you for reply is this done on Star ?
by Automod
Sat Sep 21, 2019 6:32 pm
Forum: Diagnostic discussion
Topic: Merc E220 bluetec 2015
Replies: 7
Views: 413

Merc E220 bluetec 2015

Good evening all. Has anyone had experience with an 8 wire nox sensor. I have a mercedes c220 bluetec 2015 with a code P229f x2 which will not go away, I have replaced the sensor but the code remains, I have tested all powers going in and earths, traced all wires back to ecu in the boot which is con...
by Automod
Mon Sep 16, 2019 8:46 am
Forum: Help me fix my car
Topic: Help for the newbie
Replies: 10
Views: 487

Re: Help for the newbie

Good morning all, Well to cut a long story short... This vehicle came to me after being to 4 other places, It had a problem with injector 1 and 4 cutting out. Other places had apparently replaced ecu, had injectors checked, plugs, HT leads, repaired wiring loom. But all this was done from diagnostic...
by Automod
Fri Sep 13, 2019 8:49 pm
Forum: Help me fix my car
Topic: Help for the newbie
Replies: 10
Views: 487

Re: Help for the newbie

Thank you all for help car is now fixed.
by Automod
Wed Sep 11, 2019 7:05 pm
Forum: Help me fix my car
Topic: Help for the newbie
Replies: 10
Views: 487

Re: Help for the newbie

So I got bored today and thought I would bore scope where crank sensor goes and saw something I've never seen before..... there was no normal castle flywheel to see, but there was 2 plates one had a recessed ball these where 180° apart, when the one with ball was in line with crankshaft sensor pisto...
by Automod
Wed Sep 11, 2019 7:16 am
Forum: Help me fix my car
Topic: Help for the newbie
Replies: 10
Views: 487

Re: Help for the newbie

Thank you, So in my image of the crank it wasn't showing the gap for TDC, if I had that set on DC would that of picked it up? Sorry for stupid question. I've ordered a new sensor anyway because it was a little bit out of spec, and when it comes I will scope and compare. This car is a pain in side an...
by Automod
Sun Sep 08, 2019 9:27 am
Forum: Help me fix my car
Topic: Help for the newbie
Replies: 10
Views: 487

Re: Help for the newbie

Morning Thank you for reply, I'm abit confused why I need to set to DC as these are Inductive crank sensor 2 wires in a shielded sheath, so I thought these produced AC output. Now looking at your picture, I'm guessing that top crank signal you can see a gap where I'm presuming TDC is, on mine there ...
by Automod
Sat Sep 07, 2019 6:45 am
Forum: Introductions
Topic: Newbie
Replies: 3
Views: 164

Re: Newbie

Attached is the file that works great on laptop which is what i took image from, but when trying to open on desktop just wont work.