Search found 86 matches

by Iver
Thu Sep 26, 2019 7:36 am
Forum: Diagnostic discussion
Topic: Merc E220 bluetec 2015
Replies: 7
Views: 432

Re: Merc E220 bluetec 2015

A few questions: What description do you have for P229f x2 ? Can you post a picture please ? Where did you get the new sensor ? What is guided testing telling you for that code ? traced all wires back to ecu in the boot I'm guessing you have tested for continuity, however cross contamination or a sh...
by Iver
Tue Sep 17, 2019 10:18 am
Forum: Introductions
Topic: Hello from a new chum
Replies: 3
Views: 204

Re: Hello from a new chum

Hi again ! During this learning period my aim is firstly to understand what I see happening on the screen. This is best achieved by scoping known good signals. Once you get a grasp of what is good then you should be able to spot a bad. On that vehicle there, you could introduce faults and look for t...
by Iver
Tue Sep 17, 2019 12:22 am
Forum: Diagnostic discussion
Topic: Nissan Micra K13 3 cyl cam vs crank correlation
Replies: 2
Views: 269

Re: Nissan Micra K13 3 cyl cam vs crank correlation

Have seen my share of Nissans with the Stretched Timing Chain, always throwing a P0341 but never a no start. Multiple misfire codes too. The Give away was always erratic manifold vacuum on an analogue gauge and tensioner out more than 10 mm. Visible with its hat off. This I can see is a later engine...
by Iver
Mon Sep 16, 2019 10:58 pm
Forum: Introductions
Topic: Hello from a new chum
Replies: 3
Views: 204

Re: Hello from a new chum

Hi Chum / Kim I would like to understand how it happens, even if it is an unavoidable scope artifact. Let us get the correct perspective on this. Is this waveform taken from a car that runs well or does it have negative symptoms, if so what are they? Snap Throttle is the most Treacherous and Violent...
by Iver
Mon Sep 16, 2019 12:21 am
Forum: Help me fix my car
Topic: CAN BUS LOOP
Replies: 1
Views: 149

Re: CAN BUS LOOP

Do we have to substitute a 120 ohm resistor for the removed computer Yes, it is wise to do so. As long as you KNOW that the module you removed has the 120 ohm resistor stitched in to it. If not then NO !! or can we just put a wire loop on the CAN bus terminals of the connector on the BUS side. No y...
by Iver
Mon Sep 16, 2019 12:13 am
Forum: Help me fix my car
Topic: Help for the newbie
Replies: 10
Views: 520

Re: Help for the newbie

This has now confused me even more because there doesn't seem to be a ref for TDC can anyone help me lol. The Design engineer and ECU can take the TDC reference from not only the Crank Sensor and the Missing tooth !! Go back to some BMW Diesels with the Bosch VP44 pump. For sure there are better an...
by Iver
Thu Sep 05, 2019 1:35 am
Forum: Diagnostic discussion
Topic: CAN Bus wave pattern for 2007 Jeep GC WK?
Replies: 10
Views: 592

Re: CAN Bus wave pattern for 2007 Jeep GC WK?

There is no continuity between 1 and 13. The wiring diagram must have an error.
If 1 & 13 had continuity then the two wires must be joined, Which they are not. Why would you look for continuity at 2 pins on the same plug ??

I am aware 4&5 are Grounds in the DLC!
by Iver
Mon Sep 02, 2019 8:45 pm
Forum: Diagnostic discussion
Topic: Advice needed on charging current waveform
Replies: 6
Views: 516

Re: Advice needed on charging current waveform

Let me throw in a curve ball. Are motorbikes using Smart Charge ?
by Iver
Sun Sep 01, 2019 10:43 pm
Forum: Introductions
Topic: Automotive diagnostics engineer
Replies: 2
Views: 211

Re: Automotive diagnostics engineer

Plenty More than 90% of Garage owners and their Technicians will boast, yes boast, that electronics in cars is all wrong and they cannot understand it. Yet the Boeing 747 celebrates its 50th Birthday. Visit 20 Garages in your city and ask the technicians a question, which component has terminals mar...
by Iver
Sun Sep 01, 2019 10:34 pm
Forum: Introductions
Topic: Hi Guys, TECHMAN here from St.Maarten the sunny island saying hello
Replies: 2
Views: 203

Re: Hi Guys, TECHMAN here from St.Maarten the sunny island saying hello

Hi Buddy.
Be sure to look at the Videos, Tutorials, Case Studies.

You will be an expert scoper in no time.

Scanner Danner on You Tube is unbeatable as a start to utilising Pico. Make good use of that, just my 2 cents.