Search found 619 matches
- Sat Jan 09, 2016 4:51 pm
- Forum: PicoScope 6 Automotive software
- Topic: Custom Probe - combining 2 channels
- Replies: 12
- Views: 17938
Re: Custom Probe - combining 2 channels
you won't catch me sat for hours neither waiting for DMM to change, I would employ amps clamp first for an idea of time/consumption/location but I'm not here for you to tell me how to find a draw & vice versa, if I really wanted to I'd go spend on a Flir not a 4425.
- Sat Jan 09, 2016 4:11 pm
- Forum: PicoScope 6 Automotive software
- Topic: Custom Probe - combining 2 channels
- Replies: 12
- Views: 17938
Re: Custom Probe - combining 2 channels
............... I'll carry on with my DMM :roll: One thing for a fact is I won't be buying the new scope, if I'd have known about TiePie before buying my 4423 I would have bought one as it already had differential input channels & sure connect.............. if I bought the new scope how long before ...
- Tue Jan 05, 2016 4:05 pm
- Forum: PicoScope 6 Automotive software
- Topic: volts to pressure
- Replies: 4
- Views: 5038
Re: volts to pressure
Hi guys I'm looking to convert a voltage signal from a bosch FRP sensor into a scale for reading pressure. Also I'm only looking at reading up to 400bar with this sensor so only over 2v needed on the scale. could anyone remind me how to set this up? I should know but its been a while since i messed...
- Mon Nov 30, 2015 6:55 pm
- Forum: Introductions
- Topic: Hello
- Replies: 8
- Views: 5176
Re: Hello
i see the views/downloads of the PSD file but maybe if you post a screenshot of the point of interest........
- Mon Nov 30, 2015 5:07 pm
- Forum: Introductions
- Topic: Hello
- Replies: 8
- Views: 5176
Re: Hello
maybe most people are looking on IPad's etc & can't open PSD files capiche ?
- Mon Nov 23, 2015 12:01 am
- Forum: Case studies
- Topic: How to measure a Bosch LSU 4.9 wideband lambda sensor
- Replies: 44
- Views: 58378
Re: How to measure a Bosch LSU 4.9 wideband lambda sensor
.This adapter converts very small current into a milli volt output signal. The only drawback by using the method of measurement is, that you has to break into the circuit, but besides this are there no other drawbacks. This would depend on what type of coupling scope you're using because the device...
- Wed Nov 18, 2015 7:08 pm
- Forum: Diagnostic discussion
- Topic: 24 Volt battery testing.
- Replies: 4
- Views: 6481
Re: 24 Volt battery testing.
However I have a question about terminology (sorry, now off topic from 24v to more general 6/12 or 24v batteries) ... while I'm very happy to use the term "Volt Drop" to describe the drop between two ends of a cable etc, I think using the same term to describe the "depression" in voltage of the bat...
- Fri Nov 13, 2015 1:37 pm
- Forum: Diagnostic discussion
- Topic: Passat 1,9 PD TDI bad noise
- Replies: 2
- Views: 2818
Re: Passat 1,9 PD TDI bad noise
Torsion value ?
Ask previous repairer if they used the correct tool for the rear oil seal/reluctor fitment along with CKP timing tool ?
Ask previous repairer if they used the correct tool for the rear oil seal/reluctor fitment along with CKP timing tool ?
- Tue Oct 13, 2015 9:55 am
- Forum: Case studies
- Topic: How to measure a Bosch LSU 4.9 wideband lambda sensor
- Replies: 44
- Views: 58378
Re: How to measure a Bosch LSU 4.9 wideband lambda sensor
cheers Brett, nice to know to keep my next scope options open 

- Sun Oct 04, 2015 7:43 pm
- Forum: Help me fix my car
- Topic: Looking for Insights in diagnosis of a Large POP On accel
- Replies: 4
- Views: 3988
Re: Looking for Insights in diagnosis of a Large POP On acce
Set up Pico to record Ignition while at speed. Revving up engine in stall didn't seem to show a problem before and still not now Brake torque ? Adjustable spark tester ? Have a look in the Autonerdz shop for ignition secondary leads (look at a sync probe whilst you're there) I'm sure they did a set...