Search found 52 matches

by s4c
Sun Mar 15, 2020 12:19 am
Forum: Case studies
Topic: High pressure fuel sensor no ground, SENT signal
Replies: 11
Views: 29917

Re: High pressure fuel sensor no ground, SENT signal

Hi Ben

Do you have the psdata file for the EGR pressure sensor so we can have a play with it?

Regards

Simon
by s4c
Fri Mar 06, 2020 6:01 pm
Forum: Diagnostic discussion
Topic: Renault Kangoo K9K diesel no start
Replies: 9
Views: 14515

Re: Renault Kangoo K9K diesel no start

Hi Dieseler

You need to start a different thread for the issue you have and supply a lot more information if you want the the professional techs on here to give up their valuable time to help you
by s4c
Sun Aug 25, 2019 3:28 am
Forum: Diagnostic discussion
Topic: Cylinder contribution
Replies: 7
Views: 7305

Re: Cylinder contribution

Iver

Do you have a picture of your setup?

Regards
by s4c
Tue Feb 12, 2019 6:31 pm
Forum: PicoScope 6 Automotive software
Topic: Pico software V6.13.14.4038
Replies: 4
Views: 6810

Re: Pico software V6.13.14.4038

Hi Ben

Many thanks for the explanation.

Simon
by s4c
Tue Feb 12, 2019 8:12 am
Forum: PicoScope 6 Automotive software
Topic: Pico software V6.13.14.4038
Replies: 4
Views: 6810

Re: Pico software V6.13.14.4038

Hi

Thanks for the reply.
I do have the Automotive software loaded.

Regards

Simon
by s4c
Mon Feb 11, 2019 9:12 pm
Forum: PicoScope 6 Automotive software
Topic: Pico software V6.13.14.4038
Replies: 4
Views: 6810

Pico software V6.13.14.4038

Hi I have just loaded the latest software version and have noticed that the customer information tab in 'DETAILS' is now missing. In the past, I have been diligent with logging vehicle reg and customer details and now it appears that is all lost. Is there a reason for this function being removed? Re...
by s4c
Sun Nov 25, 2018 6:21 pm
Forum: Diagnostic discussion
Topic: Great Wall X200 Cam crank waveform
Replies: 3
Views: 5844

Re: Great Wall X200 Cam crank waveform

Hi We managed to get this vehicle going. It appears that the Delphi piezo injectors have to be bled after any type of work done around the cylinder head otherwise they can seize. The garage removed them and they were sent away to the local diesel specialists who unseized them and the vehicle now run...
by s4c
Wed Nov 14, 2018 7:59 am
Forum: Diagnostic discussion
Topic: Great Wall X200 Cam crank waveform
Replies: 3
Views: 5844

Great Wall X200 Cam crank waveform

Hi I am after a camshaft vs crankshaft waveform for a 2013 Great Wall X200 with a GW4D20 Delphi controlled engine. I have looked on the waveform database but nothing is listed. The head gasket was replaced. Fuel pressure is as desired on cranking but there is no injection trigger. I am desperate to ...
by s4c
Wed May 10, 2017 10:24 pm
Forum: Diagnostic discussion
Topic: CAN BUS question
Replies: 7
Views: 11301

Re: CAN BUS question

P.S. Think this thread should be in diagnostic discussion!
You could be right, but I started this post as a software question!

I will check log and report back

Simon
by s4c
Wed May 10, 2017 2:02 am
Forum: Diagnostic discussion
Topic: CAN BUS question
Replies: 7
Views: 11301

Re: CAN BUS question

HI Mark Thanks for taking the time to answer this one. 'Can you see the fuel level as a data parameter in the BCM and can you then do the same for the cluster,' BCM does not show fuel tank level, however, cluster shows 0% 'Does the Cluster have a trip computer i.e. fuel range, fuel consumption etc' ...