Search found 50 matches

by s4c
Sun Aug 25, 2019 3:28 am
Forum: Diagnostic discussion
Topic: Cylinder contribution
Replies: 7
Views: 308

Re: Cylinder contribution

Iver

Do you have a picture of your setup?

Regards
by s4c
Tue Feb 12, 2019 6:31 pm
Forum: PicoScope 6 Automotive software
Topic: Pico software V6.13.14.4038
Replies: 4
Views: 528

Re: Pico software V6.13.14.4038

Hi Ben

Many thanks for the explanation.

Simon
by s4c
Tue Feb 12, 2019 8:12 am
Forum: PicoScope 6 Automotive software
Topic: Pico software V6.13.14.4038
Replies: 4
Views: 528

Re: Pico software V6.13.14.4038

Hi

Thanks for the reply.
I do have the Automotive software loaded.

Regards

Simon
by s4c
Mon Feb 11, 2019 9:12 pm
Forum: PicoScope 6 Automotive software
Topic: Pico software V6.13.14.4038
Replies: 4
Views: 528

Pico software V6.13.14.4038

Hi I have just loaded the latest software version and have noticed that the customer information tab in 'DETAILS' is now missing. In the past, I have been diligent with logging vehicle reg and customer details and now it appears that is all lost. Is there a reason for this function being removed? Re...
by s4c
Sun Nov 25, 2018 6:21 pm
Forum: Diagnostic discussion
Topic: Great Wall X200 Cam crank waveform
Replies: 3
Views: 547

Re: Great Wall X200 Cam crank waveform

Hi We managed to get this vehicle going. It appears that the Delphi piezo injectors have to be bled after any type of work done around the cylinder head otherwise they can seize. The garage removed them and they were sent away to the local diesel specialists who unseized them and the vehicle now run...
by s4c
Wed Nov 14, 2018 7:59 am
Forum: Diagnostic discussion
Topic: Great Wall X200 Cam crank waveform
Replies: 3
Views: 547

Great Wall X200 Cam crank waveform

Hi I am after a camshaft vs crankshaft waveform for a 2013 Great Wall X200 with a GW4D20 Delphi controlled engine. I have looked on the waveform database but nothing is listed. The head gasket was replaced. Fuel pressure is as desired on cranking but there is no injection trigger. I am desperate to ...
by s4c
Wed May 10, 2017 10:24 pm
Forum: Diagnostic discussion
Topic: CAN BUS question
Replies: 7
Views: 2011

Re: CAN BUS question

P.S. Think this thread should be in diagnostic discussion!
You could be right, but I started this post as a software question!

I will check log and report back

Simon
by s4c
Wed May 10, 2017 2:02 am
Forum: Diagnostic discussion
Topic: CAN BUS question
Replies: 7
Views: 2011

Re: CAN BUS question

HI Mark Thanks for taking the time to answer this one. 'Can you see the fuel level as a data parameter in the BCM and can you then do the same for the cluster,' BCM does not show fuel tank level, however, cluster shows 0% 'Does the Cluster have a trip computer i.e. fuel range, fuel consumption etc' ...
by s4c
Mon May 08, 2017 2:08 am
Forum: Diagnostic discussion
Topic: CAN BUS question
Replies: 7
Views: 2011

CAN BUS question

Hi I am working on a 2007 Fiat Ducato with a fuel gauge not working. We have checked the tank sensor circuit to BCM and all is good. The BCM then sends the fuel message on the network via CAN to the cluster. I can operate the fuel gauge via the scan tool showing the CAN network is potentially good. ...
by s4c
Fri Oct 07, 2016 8:08 am
Forum: Diagnostic discussion
Topic: Ford Transit cam vs crank wavform
Replies: 9
Views: 4042

Re: Ford Transit cam vs crank wavform

Hi EAAD

Sorry its taken so long to come back to you.

The filter was allowing air into the system and causing a low pressure in the fuel rail. The PCM wouldn't trigger the injectors because the fuel pressure hadn't reached the threshold required for starting.

I hope this helps

Simon