Search found 210 matches

by Dcunning35
Thu Feb 27, 2020 3:49 pm
Forum: Help me fix my car
Topic: Volvo C 30 D (Ford 2.0 engine)
Replies: 5
Views: 862

Re: Volvo C 30 D (Ford 2.0 engine)

Hi cam code , can I ask what the actual symptom is and under what conditions it occurs ( full load) etc .
After the DTC is logged will it restart straight away? .
My first check would be to check the low pressure fuel system for drawing air a vacuum test is best,then check for flow too.
Danny
by Dcunning35
Wed Feb 26, 2020 9:37 pm
Forum: Help me fix my car
Topic: Help
Replies: 4
Views: 825

Re: Help

Is this a dv6 econetic model (vaporiser) front lh corner of the dpf cat assy? The vaporiser is only fed by a very low pressure lift pump , I'd be looking for a restricted vaporiser ,see if you can create and hold vacuum on the vaporiser fuel line connection at the vaporiser if you can it's blocked!!...
by Dcunning35
Sun Mar 03, 2019 6:49 pm
Forum: Diagnostic discussion
Topic: Hall effect not pulling down to 0v
Replies: 7
Views: 1408

Re: Hall effect not pulling down to 0v

Are you sure this is a hall sensor and not magneto resistive .
Just a thought before you get two bogged down
by Dcunning35
Tue Nov 27, 2018 10:31 pm
Forum: Help me fix my car
Topic: 2005 Focus 1.4 immobiliser problem
Replies: 2
Views: 678

Re: 2005 Focus 1.4 immobiliser problem

Check the connectors on the underside of the gem module or as you call it bcm .
Sounds like he has knocked one of the snail cams than secure the connectors latched this would give you the symptoms described and usually an implausible ambient temperature reading .
by Dcunning35
Mon Oct 22, 2018 10:24 am
Forum: Diagnostic discussion
Topic: P1166 fuel deviation is this a rare EMI case? PLEASE HELP
Replies: 14
Views: 7399

Re: P1166 fuel deviation is this a rare EMI case? PLEASE HEL

The egr is quite common to short the reference voltage in these engines in fords , it usually spikes the frp giving a code respectively for the fuel pressure deviation and bloody never gives an egr code or ref voltage code in my opinion poor calibration of the dtcs . But well done for your persisten...
by Dcunning35
Tue Sep 04, 2018 7:35 pm
Forum: Help me fix my car
Topic: 2006 ford focus st 2.5 eng. HYDA running fault
Replies: 1
Views: 790

Re: 2006 ford focus st 2.5 eng. HYDA running fault

Hi ,a can communication error wouldn't result in hunting at idle and no throttle response.
So lets start again have you any dtcs stored?
Id be starting with basics air leaks on the intake , but let me know on the dtc,s etc and il try and assist.
Danny
by Dcunning35
Fri Aug 24, 2018 8:19 am
Forum: Help me fix my car
Topic: ford transit connect 2012 DPF issues
Replies: 4
Views: 3179

Re: ford transit connect 2012 DPF issues

Ok koeo 0.49v At idle servicable dpf around 0.5 to 0.6v At 2000 rpm if your seeing 0.8 it is loaded but requires regen If over 1 volt it will log the soot accumulation dtc with different failure mode and status this impeads drive to regen and service regen. If you want a matrix for the sensor I have...
by Dcunning35
Sun May 20, 2018 7:16 pm
Forum: Help me fix my car
Topic: Vauxhall adam.1.2petrol engine control unit reset
Replies: 2
Views: 1012

Re: Vauxhall adam.1.2petrol engine control unit reset

Apologies a12xel is the engine code .
The pcm is acdelco e78.
Thanks
Danny
by Dcunning35
Thu May 17, 2018 7:26 pm
Forum: Help me fix my car
Topic: Vauxhall adam.1.2petrol engine control unit reset
Replies: 2
Views: 1012

Vauxhall adam.1.2petrol engine control unit reset

Im hoping someone with Vauxhall product knowledge can help me out. I have an adam with a reference voltage failure requiring a pcm . I have access to aribtes commander which will read,reset and program the pin code. I sourced a replacement online assured it had been reset with mdi so had no code pre...
by Dcunning35
Sun Apr 29, 2018 7:52 am
Forum: Help me fix my car
Topic: 2013 Ford transit connect dpf fault.
Replies: 2
Views: 2911

Re: 2013 Ford transit connect dpf fault.

Your quite right the vaporizer glow plug is supplied with battery voltage via the relay , my advice is to bridge pins 3 and 5 at the relay and volt drop the circuit using a 21w bulb to load it in place of the vaporizer. It shouldn't be to hard to prove your therory of there being a load in the wirin...