Search found 43 matches

by landroverman1958
Fri May 08, 2020 11:35 am
Forum: Help me fix my car
Topic: Errors after replacement engine
Replies: 6
Views: 8721

Re: Errors after replacement engine

Those fault codes are usually from a crank camshaft corrolation problem,usually when the crank sensor reluctor ring surface is damaged for whatever reason,the ecu sees a problem with the signal quality over a certain crank speed,check the crank sensor output signal,
by landroverman1958
Thu Apr 23, 2020 11:51 am
Forum: Help me fix my car
Topic: Boxer 3.0 2011 no Speedo
Replies: 6
Views: 9277

Re: Boxer 3.0 2011 no Speedo

What type of speed sensor is on the gearbox?how many wires? is there an input signal @the instrument cluster,
by landroverman1958
Sat Nov 23, 2019 10:48 am
Forum: Help me fix my car
Topic: Help with ignition wave form
Replies: 2
Views: 3744

Re: Help with ignition wave form

Good morning, how does that help,saying that the exspensive scan tool would be fried?Ah but of course it is a scan tool as well so it enables the operator to view live data and scope at the same time. i may have missed the introduction of the scan tool side on the pico? i dont mind being corrected a...
by landroverman1958
Tue Aug 20, 2019 6:01 am
Forum: Diagnostic discussion
Topic: Peugeot 407 crank non start Cam/Fuel Pressure
Replies: 2
Views: 10872

Re: Peugeot 407 crank non start Cam/Fuel Pressure

Hi Chris,1st things 1st, check the voltage at the rail pressure sensor,koeo hould be around .5volt,then unplug sensor to see if the voltage goes up to reference voltage,possibly 5volts. Check the primary supply to the high pressure pump for good flow no aeration,if supply is good,do a cranking test,...
by landroverman1958
Tue Aug 13, 2019 5:55 am
Forum: Diagnostic discussion
Topic: BMW 116i N45B16 Crank Sensor Signal
Replies: 7
Views: 7997

Re: BMW 116i N45B16 Crank Sensor Signal

Hi have you got your sample rate turned up enough?I have,nt seen a crank signal like that on that type of engine,
by landroverman1958
Fri Aug 09, 2019 4:44 pm
Forum: Help me fix my car
Topic: 2013 seat 2.0 CR extended crank from cold.
Replies: 5
Views: 6232

Re: 2013 seat 2.0 CR extended crank from cold.

Good evening,sounds like you have an high pressure leak possibly an a injector leaking back,why dont you carry out a back leakage check,and or koeo crank with the injectors disconnected electrically,and observe rail pressure rise?has this engine got an electrical connector for a pressure regulator?p...
by landroverman1958
Fri Aug 09, 2019 5:52 am
Forum: Help me fix my car
Topic: 2013 seat 2.0 CR extended crank from cold.
Replies: 5
Views: 6232

Re: 2013 seat 2.0 CR extended crank from cold.

Hi just check the current drawn by the in tank fuel pump,through the access point under the rear seat,o/s usually,8 to 10 amps,using an amp clamp,watch initial turn on and will probably just show a prime pulse.
by landroverman1958
Sun Jul 07, 2019 9:45 am
Forum: Help me fix my car
Topic: Intake vaccum with wps500
Replies: 1
Views: 3078

Re: Intake vaccum with wps500

Good morning,why dont you put the pressure sensor in the exhaust?that way you can see if you have any exhaust un eveness,or do an in cylinder pressure reading. :idea:
by landroverman1958
Fri Jun 28, 2019 5:34 pm
Forum: Help me fix my car
Topic: Test Plan for Smart Charging System on Ford Fiesta 1.4 (SPJC)
Replies: 20
Views: 20943

Re: Test Plan for Smart Charging System on Ford Fiesta 1.4 (SPJC)

Just a thought......Overheated engine?or did i miss read,what does the temperature sensor show?incorrect temperature tells ecu to charge at a lower voltage level because it thinks the coolant temp is too high? Also check the ignition main relay in the underbonnet fuse box for corrosion on pins causi...
by landroverman1958
Mon Jun 17, 2019 6:55 pm
Forum: Help me fix my car
Topic: Rav4 fault code 78(8)
Replies: 6
Views: 12198

Re: Rav4 fault code 78(8)

Good evening Burt,has the fuel rail got two electrical connectors one at each end of the high pressure rail?what model year is the Rav4? If it has two connectors the one is the fuel rail pressure sensor,the other one the other end is the pressure control solenoid,the rail sensor measures the pressur...