Search found 29 matches

by bullstar
Tue Jan 17, 2017 10:44 pm
Forum: Help me fix my car
Topic: CanBus on Transit Custom
Replies: 18
Views: 30403

Re: CanBus on Transit Custom

Hi STC thanks for your explanation on this, So when looking at can signals apart from seeing lines shorted etc, I should be looking for the 2.0v difference as in your drawing, So in frame 27 where the voltage is lower than 2.0v is this indicate a fauty node or connector. I did say in my post that I ...
by bullstar
Tue Jan 17, 2017 7:53 pm
Forum: Help me fix my car
Topic: CanBus on Transit Custom
Replies: 18
Views: 30403

CanBus on Transit Custom

transit 2014 canbus.psdata Transit custom 2014 model 2.2 tdci came in to and diagnostic tool came up with 11 faults and most were "U" Codes no coms to Nodes so looked like a can bus fault, I set up the canbox and looked at can H and L , These were the results, My question is does this look correct ...
by bullstar
Wed Oct 19, 2016 7:37 am
Forum: Diagnostic discussion
Topic: Volvo v70 misfire
Replies: 7
Views: 8972

Re: Volvo v70 misfire

Hi, thanks for your input , yes a cylinder leakage is the next test we going to do on this car , I believe the car is similar to the test results as the valve train also sounds a little noisy and could be the symptoms of valve lash.
by bullstar
Sun Oct 16, 2016 2:44 pm
Forum: Diagnostic discussion
Topic: Volvo v70 misfire
Replies: 7
Views: 8972

Re: Volvo v70 misfire

Thanks for your input, I was thinking it was the exhaust stoke as if I put the rulers up in degrees from compression peak to peak 720 degrees the 0.8 bar is in exhaust stroke, Surely There should be no peak on a compression test
by bullstar
Sat Oct 15, 2016 5:58 pm
Forum: Diagnostic discussion
Topic: Volvo v70 misfire
Replies: 7
Views: 8972

Volvo v70 misfire

Hi, Just bought a wps so thought I would try it on a misfiring Volvo 1999 model 10 valve, following the software instructions I did a compression test, the figures on all 5 cyls were identical around 167 psi but I'm not sure what the small peaks are , is this a valve reading? with a vacuum gauge I'm...
by bullstar
Sat Oct 15, 2016 5:38 pm
Forum: Diagnostic discussion
Topic: CanBus on nissan Qashqai
Replies: 10
Views: 25589

Re: CanBus on nissan Qashqai

Thanks for all your comments , I did reset the ECU learning data but would say all done but then comeback saying partially full again. Any how after contacting Nissan they told me the customer was told to fetch the car back regarding a recall of the software within the ECU but the customer never ret...
by bullstar
Fri Sep 09, 2016 9:08 pm
Forum: Diagnostic discussion
Topic: Vauxhall / Opel Vivaro 1.9 - 2002 - F9Q
Replies: 3
Views: 8712

Re: Vauxhall / Opel Vivaro 1.9 - 2002 - F9Q

Them customers just make me smile ! I usually charge them double :lol:
by bullstar
Fri Sep 09, 2016 8:10 pm
Forum: Diagnostic discussion
Topic: CanBus on nissan Qashqai
Replies: 10
Views: 25589

Re: CanBus on nissan Qashqai

Sorry for the late reply! STC forgive me messing with your mental health I have that problem with most people ! What I meant was I can talk to ABS module and parameters which are throwing C1130 and C1132 codes and what this is saying is the ABS unit is not able to talk to engine control module. Scan...
by bullstar
Wed Aug 24, 2016 4:44 pm
Forum: Diagnostic discussion
Topic: CanBus on nissan Qashqai
Replies: 10
Views: 25589

Re: CanBus on nissan Qashqai

Hi, thanks for your reply, I'm not sure what you mean by "What network does the scan tool ride on for Serial Communication" , I'm using a hella gutmann scan tool. I can communicate ok with ABS/ESP unit and check parameter's, sometimes the esp lights do go out if I clear p0471 but they come back show...
by bullstar
Wed Aug 24, 2016 12:01 pm
Forum: Diagnostic discussion
Topic: CanBus on nissan Qashqai
Replies: 10
Views: 25589

CanBus on nissan Qashqai

Nissan Qashqai 1.5dci 2012 , car is running ok but esp slip lights are on , codes are c1130 and c1132 no coms with the ecm, also have some codes stored on body control and other ecu U1000 , also p0471 logged but dpf pressure sensor reading as should and tested with mityvac and dvom , could this be a...