Search found 119 matches

by GRUSS
Sun Jul 06, 2014 5:48 pm
Forum: Automotive kit hardware
Topic: Some decent laptop diagnostic software recommendations
Replies: 2
Views: 9081

Some decent laptop diagnostic software recommendations

I've had my texa navigator mobile for a few years now, it's complete in the 2 boxes with all leads and hasp key etc. Runs great on windows 7 with my SSD. However... The last few jobs where I've really needed it, it's let me down badly. So I think I'm going to sell it and get something else that will...
by GRUSS
Wed Sep 04, 2013 12:02 pm
Forum: Help me fix my car
Topic: Mondeo 2.0 TDCI non start
Replies: 9
Views: 6952

Re: Mondeo 2.0 TDCI non start

I did reply earlier but seems to have gone AWOL!?!

It's a 2005.
by GRUSS
Tue Sep 03, 2013 8:51 pm
Forum: Help me fix my car
Topic: Mondeo 2.0 TDCI non start
Replies: 9
Views: 6952

Re: Mondeo 2.0 TDCI non start

Thanks for clearing that up for me...

I've done a few that have lost injection coding but all these are correct.

is it possible to do a leak off with the engine not running?

Heard the filters can block on these?
by GRUSS
Tue Sep 03, 2013 8:33 pm
Forum: Help me fix my car
Topic: Mondeo 2.0 TDCI non start
Replies: 9
Views: 6952

Mondeo 2.0 TDCI non start

I'm not a ford man but a family member has asked me to look at there mondeo. It cut out and wouldn't restart whilst driving. Hooked up my Texa and retrieved P2291 injector control pressure too low- engine cranking. Looking at live data whilst cranking I'm getting 75bar max fuel pressure. I've checke...
by GRUSS
Thu Jun 13, 2013 6:35 am
Forum: Diagnostic discussion
Topic: 2008 Vauxhall Vivaro piezo injector currents
Replies: 17
Views: 11626

Re: 2008 Vauxhall Vivaro piezo injector currents

You have to remove the plastic scuttle, wiper linkage and heater box then finally unbolt the metal part of the scuttle. Behind that is a very rubbish foam seal which lets water pass straight through. If you cover the engine and pour water on the screen you'll probably see where it's leaking through....
by GRUSS
Wed Jun 12, 2013 8:35 pm
Forum: Diagnostic discussion
Topic: 2008 Vauxhall Vivaro piezo injector currents
Replies: 17
Views: 11626

Re: 2008 Vauxhall Vivaro piezo injector currents

Make sure you remove the full scuttle panel and reseal it other wise water will just fill the cylinder head back up.
I've also PM'ed you about programming the injector
by GRUSS
Sat Jun 08, 2013 8:01 pm
Forum: Diagnostic discussion
Topic: Acc. Pedal Position
Replies: 14
Views: 9150

Re: Acc. Pedal Position

Same here, can't see the waveform but if your getting drop outs on sensor 2 then it's just a ground check as Paul as mentioned. Spoke to vx technical a few times about this.
by GRUSS
Thu Mar 28, 2013 11:42 pm
Forum: Diagnostic discussion
Topic: Renault Master P1882
Replies: 6
Views: 9100

Re: Renault Master P1882

What's the DTC description?
by GRUSS
Wed Mar 27, 2013 5:46 pm
Forum: Diagnostic discussion
Topic: can bus problem or software fault ?
Replies: 16
Views: 14399

Re: can bus problem or software fault ?

When you had tech 2 did you carry out a Ecu presence check?

Power the car down, ie ign. Off and measure the resistance across pins 6+14. Should be 60 ohms.

Next connect your scope to 6 and ground and 14 and ground (I can't view the files you've uploaded)

Has the gearbox been out?
by GRUSS
Sat Mar 23, 2013 4:54 pm
Forum: Diagnostic discussion
Topic: Vauxhall Zafira idle fluctuation
Replies: 5
Views: 5473

Re: Vauxhall Zafira idle fluctuation

You have PM