Automotive Guided Tests

Our PicoScope Automotive software contains over 160 guided tests and includes example waveforms and scope settings. These waveforms were captured using a PicoScope Automotive Diagnostics Kit, find out more about our kits here.  

Home

Actuators

GDI injector current

The purpose of this test is to evaluate the operation of the Gasoline Direct Injection (GDI) injector control circuit, switching signal and solenoid mechanism.

Warning icon (exclamation mark in circle)

This test involves taking measurements on a system or component having a potentially hazardous voltage.

Risk of damage to equipment and property, and risk of electric shock, personal injury, or death.

  • Always follow manufacturers' safety instructions and working practices.
  • Ensure the equipment and accessories have a voltage rating that meets or exceeds the possible test voltages.

How to perform the test

  • Use manufacturer's data to identify the injector power supply circuit.
  • Connect the low amps clamp to PicoScope Channel A.
  • Select the 20 A scale and zero the clamp before connecting to the injector power supply circuit.
  • Minimize the help page. You will see that PicoScope has displayed an example waveform and is preset to capture your waveform.
  • Start the scope to see live data.
  • Start and run the engine.
  • With your waveforms on screen stop the scope.
  • Turn off the engine.
  • Use the Waveform Buffer, Zoom and Measurements tools to examine your waveform.

Example waveform

Injector current waveform during engine cranking conditions.

Injector current waveform during engine cranking conditions.

Further guidance

Guide

A Gasoline Direct Injection (GDI) injector delivers fuel directly to the air charge within a cylinder.

GDI injector fast reaction times enable an engine management system to operate across different cylinder charge modes, for example:

  • a homogenous air charge having the same stoichiometric air-fuel mixture throughout the combustion volume; or
  • a heterogeneous air charge having a stratified air-fuel mixture with a small fuel rich volume within an overall lean combustion volume.

GDI injectors can deliver fuel with complex spray patterns and provide multiple injections per compression stroke. Furthermore, fuel can be kept from the cylinder volume until very close to the point of ignition reducing the risk of pre-ignition or knock and allowing the use of higher compression ratios, all of which leads to better thermal and fuel efficiencies.

As fuel injection coincides with the compression stroke, GDI injection pressures must be sufficient to overcome the in-cylinder pressures that occur across all engine load conditions. Therefore, GDI systems require a high pressure, up to 200 bar, fuel delivery system consisting of a common fuel rail supplied by a high-pressure fuel pump.

The ECM improves GDI injector response times by increasing the circuit voltage during the opening phase providing additional energy to move the valve rapidly. However, once the valve is fully open, only a relatively small voltage is necessary to hold it place, which the ECM maintains with a lower, pulsed, square-wave voltage.

GDI injector failures may cause loss of engine performance, misfire, or excessive smoking symptoms. Possible failure modes may be:

  • Mechanical inlet or outlet blockages, sticky/stuck injector valves or defective spray patterns.
  • Electrical open or short circuits and high resistances in the wiring or solenoids.
  • Internal ECM faults.

When operating out of their normal tolerances, for example repeated short runs or cold start operations, excessive soot may build up within the engine systems and cause a variety of secondary issues (e.g. blocked inlets, EGR valves, turbo vanes etc.). As such, regular maintenance is essential for continued operation within tolerances.

Diagnostic trouble codes

  • P0200
  • P0201
  • P0202
  • P0203
  • P0204
  • P0205
  • P0206
  • P0207
  • P0208
  • P0209
  • P0210
  • P0211
  • P0212
  • P0213
  • P0214
  • P0216
  • P0261
  • P0262
  • P0263
  • P0264
  • P0265
  • P0266
  • P0267
  • P0268
  • P0269
  • P0270
  • P0271
  • P0272
  • P0273
  • P0274
  • P0275
  • P0276
  • P0277
  • P0278
  • P0279
  • P0280
  • P0281
  • P0282
  • P0283
  • P0284
  • P0285
  • P0286
  • P0287
  • P0288
  • P0289
  • P0290
  • P0291
  • P0292
  • P0293
  • P0294
  • P0295
  • P0296

Disclaimer

This help topic is subject to changes without notification. The information within is carefully checked and considered to be correct. This information is an example of our investigations and findings and is not a definitive procedure. Pico Technology accepts no responsibility for inaccuracies. Each vehicle may be different and require unique test settings.

`